Installation
instructions
Shift selector illuminated plate
fitting for BMW E32 & E34, all models with automatic g/b
This unit provides illumination to the shift selector panel. The unit employs several small chip LEDs
and microcomputer control. A special
noise signal is used to prevent line noise from generating false-starts or
miss-operation.
1. Field of application
The microprocessor reads your car selector type automatically and
displays the correct selector illumination pattern by LEDs.
2. Introduction
This device comes preset with the optimum illumination of the shift
selector plate. Two variable controllers allow the user to set the brightness
of the illumination mode and selected mode lamp panel.
3. Safety instructions
In developing this unit special attention was paid to operating safety
and easy of use. The appliance is resistant to moisture, dirt, various oils and
liquids as well as small mechanical jolts.
4. Installation Steps
To install the unit please follow the procedure given below. Please be
careful with any electric wires or connectors to prevent shorting.
1.
Please be careful to park your car on a flat area; you
will have to be able to move the shift selector freely. First set the parking brake before
commencing the installation. Insert
and turn the Key to Steering lock release position and hold it and press the
brake pedal. This will allow you to move the gear selector to 1st or
2nd position for removal of the shift handle.
2.
After pulling out the shift handle, ease out the S/E
or S/A switch by a small plus driver, and release the connector.
3.
Put your finger into the switch hole and pull up the
wood panel from the hole side side; slide the wood panel forward and then lift it over the the shift stub
very carefully from the back and remove it.
4.
Please find 2 connectors (one connected to the shift
selector and the other to S/E or S/A switch). Then
cut or splice into the cable all four cables to the shift
connector. The other three cable must be connected to
ACC illumination and ground, you can find illumination and ground line at S/E
or S/A switch but they donft have any ACC line. So please find out ACC line
something like Radio unit or another connector.
In
the photos shown below, my car had one free white connector in which the green
line was for ACC -- I cut it to supply the unit.
5.
There are two types of BMW original selector panel,
please check which type of panel you have. If yours is the earlier type, you'll need to
cut the original panel slightly (see cut sample photo). If your panel is the
later model you donft have any extra fitting work, it is very easy to install
the LED panel.
(Later model sample) – 1/2
inch deep -
(Earlier model sample) – 1/4
inch deep - cut slightly red square
6.
After connecting all cables, please fit it to the
panel. Move the shift selector to
parking position and turn the ignition on for LED panel test. If your electrical connections are fine,
it will correctly
light up. (If something is wrong or the system can not understand your car, the
red LED will flash many times as an alert.)
7.
Please move the shift selector to test all position
with illuminated on mode (night mode).
If you would like to change the brightness you can reset the variable
resistors; NOTE. they
are very small so please be gentle with them.
8.
After all tests are finished and you are happy with
the unit, remove the white
protective tape from the double-sided adhesive tape on the top indicator board
and then carefully position it on the LED panel and press down for a good fit.
5. System settings
This system is fully automated and supports all types of 4 speed and 5
speed gearboxes with AGS/EGS.
You can adjust the brightness by resetting the two variable controllers.
VR1 night
time illuminated LED output control
VR2 selection
position LED output control
This system doesnft sincronaize with illumination dimmer control, if you setting
dimmer control darker than high level position, panel illumination light
doesnft lightup or make flushing.
So please make fit control dimmer level until illumination better light
up. If you donft like changing
dimmer control, you have another choice for use this system. You may connect
illumination line to ACC line so illumination keep lightup any position to move
dimmer control, but in this case illuminatio will lightup all the time when you
driving daytime. J
6. Upgrade
If you or your
friends have knowledge about microcomputer programming, you can easily modify
or upgrade the unit by software tuning/modification.
9. Overview of models
5 series E34 4
speed 5 speed
7 series E32 4
speed 5 speed
10. Technical info
Connecting
wire
Unit package (4 speed panel)
We reserve the right to make technical changes as deemed necessary.
©Copyright 2008 Shogun
& Take& Hairywithit